?
<cite id="xbn1z"></cite>
<ruby id="xbn1z"></ruby>
<span id="xbn1z"><video id="xbn1z"><ruby id="xbn1z"></ruby></video></span>
<strike id="xbn1z"><dl id="xbn1z"><del id="xbn1z"></del></dl></strike>
<ruby id="xbn1z"></ruby>
<ruby id="xbn1z"><i id="xbn1z"><del id="xbn1z"></del></i></ruby>
<strike id="xbn1z"></strike>
<strike id="xbn1z"></strike>
<ruby id="xbn1z"></ruby>
<span id="xbn1z"><dl id="xbn1z"></dl></span>
<strike id="xbn1z"></strike>
<strike id="xbn1z"><dl id="xbn1z"><del id="xbn1z"></del></dl></strike>
<strike id="xbn1z"><dl id="xbn1z"></dl></strike>
<strike id="xbn1z"><i id="xbn1z"><cite id="xbn1z"></cite></i></strike><strike id="xbn1z"><i id="xbn1z"></i></strike>
<span id="xbn1z"><dl id="xbn1z"><ruby id="xbn1z"></ruby></dl></span>
<strike id="xbn1z"></strike><strike id="xbn1z"></strike>
<span id="xbn1z"><dl id="xbn1z"></dl></span>
?

丹佛斯FC302變頻器故障代碼和報警參數說明

時間:2020-01-10    作者:津信變頻    點擊:
丹佛斯FC300系列變頻器是丹佛斯推出的主力機型變頻器,功率范圍覆蓋0.25KW到1.4MW,適用于各個行業的多種應用場合。在使用過程中如果出現故障,FC300變頻器會在面板顯示故障代碼,以便分析故障原因和采取措施,故障代碼含義如下:


故障代碼 故障描述 Warning Alarm/Trip Alarm/Trip Lock
1 10 Volts low10伏電壓低 X    
2 Live zero error斷線故障 (X) (X)  
3 No motor無電機 (X)    
4 Mains phase loss主電源缺箱 (X) (X) (X)
5 DC link voltage high直流回路電壓高 X    
6 DC link voltage low直流回路電壓較低 X    
7 DC over-voltage直流過電壓 X X  
8 DC under voltage直流欠電壓 X X  
9 Inverter overloaded逆變器過載 X X  
10 Motor ETR over temperature電動機ETR 溫度高 (X) (X)  
11 Motor thermistor over temperature電機熱敏電阻溫度高 (X) (X)  
12 Torque limit轉矩限制 X X  
13 Over Current過電流 X X X
14 Earth Fault接地故障 X X X
15 Hardware mismatch硬件不匹配   X X
16 Short Circuit短路   X X
17 Control word time-out控制字超時 (X) (X)  
22 Hoist Mech. Brake起重機械制動 (X) (X)  
23 Internal Fan Fault內部風扇故障 X    
25 Brake resistor short-circuited制動電阻短路 X    
26 Brake resistor power limit制動電阻功率限制 (X) (X)  
27 Brake chopper short-circuited制動斬波器短路 X X  
28 Brake check剎車檢查 (X) (X)  
29 Heatsink temp散熱片溫度 X X X
30 Motor phase U missing電動機缺U相 (X) (X) (X)
31 Motor phase V missing電機缺V相 (X) (X) (X)
32 Motor phase W missing電機缺W相 (X) (X) (X)
33 Inrush Fault充電故障   X X
34 Fieldbus communication fault現場總線通訊故障 X X  
36 Mains failure電源故障 X X  
37 Phase imbalance相位不平衡   X  
38 Internal Fault內部故障   X X
39 Heatsink sensor散熱片傳感器   X X
40 Overload of Digital Output Terminal 2727過載的數字輸出終端 (X)    
41 Overload of Digital Output Terminal 2929過載的數字輸出終端 (X)    
45 Earth Fault 2接地故障2 X X X
46 Pwr. card supply功率卡電源   X X
47 24 V supply low24 V電源低 X X X
48 1.8 V supply low1.8 V電源低   X X
49 Speed limit速度限制 X    
50 AMA calibration failedAMA校準失敗   X  
51 AMA check Unom  and InomAMA檢查Unom和Inom   X  
52 AMA low InomAMA低Inom   X  
53 AMA motor too bigAMA電機太大   X  
54 AMA motor too smallAMA電機太小   X  
55 AMA parameter out of rangeAMA參數范圍   X  
56 AMA interrupted by userAMA用戶中斷   X  
57 AMA time-outAMA超時   X  
58 AMA internal faultAMA內部故障 X X  
59 Current limit電源極限 X    
60 External Interlock外部互鎖 X X  
61 Feedback Error反饋錯誤 (X) (X)  
62 Output Frequency at Maximum Limit最大限度的輸出頻率 X    
63 Mechanical Brake Low機械制動器低   (X)  
64 Voltage Limit電壓限制 X    
65 Control Board Over-temperature控制板保護套 X X X
66 Heat sink Temperature Low散熱器溫度低 X    
67 Option Configuration has Changed選擇配置發生了變化   X  
68 Safe Stop安全停止 (X) (X)1)  
69 Pwr. Card Temp功率卡溫度   X X
70 Illegal FC configuration非法FC配置     X
73 Safe Stop Auto Restart安全停止自動重啟 (X) (X)  
76 Power Unit Setup功率卡設置 X    
77 Reduced power mode精簡功率模式 X    
78 Tracking Error跟蹤誤差 (X) (X)  
79 Illegal PS config非法PS配置   X X
80 Drive Initialized to Default Value驅動初始化為默認值   X  
81 CSIV corruptCSIV破壞   X  
82 CSIV  parameter  errorCSIV 參數錯誤   X  
85 Profibus/Profisafe  Error現場總線/ Profisafe錯誤   X  
90 Feedback Monitor反饋監控 (X) (X)  
91 Analogue input 54 wrong settings模擬輸入54錯誤設置     X
250 New spare part新備件     X
251 New Type Code新類型代碼   X X



返回列表
? 国产精品久久久久精品日日